|
|
|
|
|
 |
NB Series
(NB150S/NB150T)
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Features |
| 0.38 Inch Profile |
| Synchronization |
| Remote Turn On (TTL) |
| Output Voltage Trim Pin. |
| Single and Dual Outputs. |
| Over Temperature Protection. |
| Built-In Test (Output Power Good). |
| N + 1 Redundancy (Single Output). |
| MIL-STD-883 Screening (Military Version). |
| Triple Outputs are Isolated Allowing Any Combination of Output Voltages. |
| How To Order | |
| Series: | NB |
| Total Output Power: | 150 |
| Single Output: | T ("S" for Single Output) |
| Product Grade: | M ("I" for Industrial) |
| Output Voltage: | 5/15/15 |
| Options: | -C |
|
|
|
| Options | |
| A Option: | Pins out side of unit. |
| B Option: | Pins out bottom of unit. |
| C Option: | Pins out top of unit. |
| D Option: | Through hole inserts (STD threaded) 0.115 01A |
| I Option: | M2.5 inserts |
| Model
Numbering Example: To order a 150 watt, 15 Vout (single output), industrial grade power supply with pins out the bottom, the model number would be: NB150SI/15-B. Military grade would be NB150SM/15-B. To order a 150 watt, triple output, 15 Vdc, 15 Vdc and 5 Vdc, industrial grade power supply with pins out the bottom (baseplate), the model number would be: NB150TI/15/15/5.2-B. Triple output, 12 V, 15 V and 3.3 Vout, military grade, would be NB150TM/12/15/3.3-B. When ordering a triple output unit, the first output voltage in the model number is located on channel 1 (see case drawing in PDF File). |
|
|
|
|
| Accessory Products | |
| SM1275: | Input Transient Suppression Module (for 28 Vdc input only) for conformance to MIL-STD-704A & MIL-STD-1275. |
| NBF150: | EMI Filter to meet MIL-STD-461C. |
| Selection Chart Output Voltage and Output Current |
||
| Nominal Output Voltage | Single Output
Current (Amps) |
Triplel Per
Channel Current (Amps) |
|---|---|---|
| 2 | 30 | 10 |
| 3.3 | 30 | 10 |
| 5 | 30 | 10 |
| 5.2 | 28.8 | 9.6 |
| 12 | 12.6 | 4.2 |
| 15 | 10.2 | 3.3 |
| 24 | 6.3 | 2.1 |
| 28 | 5.4 | 1.8 |
| Input Characteristics | ||||
| Min | Typ | Max | Units | |
|---|---|---|---|---|
| Input Voltage | 14 | 28 | 40 | Vdc |
| Brown Out (75%) Full Load | 12 | Vdc | ||
| No Load Power Dissipation | 2 | 4 | Watt | |
| Inrush Charge | 2 | mc | ||
| Reflected Ripple Current | 15 | % | ||
| Logic Disable Current (Sink) | 100 | 150 | µA | |
| Logic Disable Power In | 1.2 | 2.5 | W | |
| Input Ripple Rejection (120 Hz) | 55 | dB | ||
| Input Ripple Rejection (800 Hz) | 45 | Vdc | ||
| Efficiency (FL) | 73 | 78-84 | % | |
| Efficiency (3.3V) (FL) | 67 | 74 | % | |
| Efficiency (3.3V) (FL) | 62 | 67 | % | |
| EMI | Units conform to MIL-STD-461C (on the input leads) with companion filter |
| Input Transient | Units conform to MIL-STD-704D (50 Vdc for 0.1 second). Up to 100 Vdc for 100 mS with SM1275 transient suppression module. |
| Output Characteristics | ||||
| Min | Typ | Max | Units | |
|---|---|---|---|---|
| Set Point Accuracy | 1* | % Vout | ||
| Load Regulation | 5 | 0.2%1 | mV | |
| Line Regulation | 5 | 0.2%1 | mV | |
| Ripple P-P (10
MHz) (2V to 24V) |
45 | 150 | mV | |
| Ripple P-P (10
MHz) (28V) |
0.2 | 1 | % Vout | |
| Trim Range | 100 | 110 | % Vout | |
| Remote Sense Compensation (Main Only) | 0.5 | Vdc | ||
| Overvoltage Protection | ||||
| (5V-28V) | 125 | % Vout | ||
| (2V-3.3V) | 140 | % Vout | ||
| Current Sharing | ±10 | % Iout | ||
| Transient Response (Vout 1%) Time / Overshoot | ||||
| 20 - 80% Load | 350 / 300 | µS/mV | ||
| Low Line - High Line | 300 / 350 | µS/mV | ||
| 50 - 100% Load | 250 / 300 | µS/mV | ||
| Temperature Drift | 0.01 | 0.05 | %/oC | |
| Long Term Drift | 0.01 | 0.02 | %/1KHrs | |
| Current Limit | 105 | 125 | 150 | % Iout |
| Short Circuit Current | 25 | 75 | % Iout | |
| Turn On Time | 1.5 | mS | ||
| Logic Turn On Time | 1.5 | mS | ||
| * = 1% or 50mV, whichever is
greater 1 = 0.2% or 25mV, whichever is greater |
||||
| Isolation Characteristics | ||||
| Min | Typ | Max | Units | |
|---|---|---|---|---|
| Isolation: Input to Output |
500 | Vdc | ||
| Output to Base | 250 | Vdc | ||
| Input to Base (28 Vdc in) |
250 | Vdc | ||
| Input to Output Capacitance |
0.066 | µF | ||
| Insulation Resistance (@50 Vdc) | 50 | MOhm | ||
| Mechanical Characteristics | ||
| Weight | 9.6 | oz |
| 270 | grams | |
| Size | 4.5 x 3.0 x 0.38 | inch |
| 114.3 x 76.2 x 9.7 | mm | |
| Volume | 5.13 | inch3 |
| 56.0 | cm3 | |
| Temperature Characteristics | ||||
| Min | Typ | Max | Units | |
|---|---|---|---|---|
| Operating | -55 | +100 | oC | |
| Storage (Ambient) | -55 | +125 | oC | |
| Over Temperature Shutdown | +105 | oC | ||
| Thermal Resistance Case - Ambient | 12 | oC/W | ||
| Environmental Screening - M Model | |
| Stabilization Bake: | +125oC for 24 hours similar to Mil-Std-883, M1108, Condition B |
| Temperature Cycling: | 10 cycles at -55oC to +125oC (transition period 36 minutes) similar to Mil-Std-883, M1010, Condition B |
| Burn-in: | 160 hours at +85oC minimum |
| Final Testing | |
| Enviroomental Screening - I Model | |
| Burn-in: | 16 hours at +85oC minimum |
| Final Testing | |
